800.292.2737 | [email protected] | aymcdonald.com 7-24 53 Engineering Engineering Blank Part No. - Contact Factory for more info. Instruction Sheets Copper Meter Setters - Brass materials meet or exceed AWWA C-800 (latest revision) - Copper tubing has a 13/16" O.D. for 5/8", 5/8" x 3/4" or 3/4" meter setters, 1 1/8" O.D. for 1" meter setters, 1 5/8" for 1 1/2" meter setters and 2 1/8" for 2" meter setters. - Solder is no-lead. - EPDM rubber gaskets are furnished as standard. Contact factory for fiber or leather gaskets. - All meter setters are factory tested air under water at 85 PSIG. - Brass support bar is standard on 18" and higher meter setters. - Meter setter heights over 24" available on special order. - All meter swivel nuts have wire seal hole. - Lockwing ball style meter valves are standard. - Meter swivel nuts with meter support saddle are standard, except on tandem style meter setters. - All copper meter setters can be supplied with a test valve on the outlet tubing. - For dual check backflow valves, see Dual Check Section. - Brace eye hole accepts 1/2" iron pipe or PVC for 5/8", 5/8" x 3/4" and 3/4" meters and 1" vertical meter setters. - Brace eye hole accepts 3/4" iron pipe for PVC for 1", horizontal meter setters. - Brace eye hole accepts 1" iron pipe or PVC for 1 1/2" & 2", horizontal meter setters. TABLE I TABLE II Page Series 750 See Series 720 ............ 324-325 Series 751 See Series 721 ............ 328-329 Series 752 See Series 722 ............ 330-331 Series 753 See Series 723 ............ 332-333 Series 754 See Series 724 ............ 334-335 Series 755 See Series 725 ............ 336-337 Series 756 See Series 726 ............ 338-339 Series 757 See Series 727 ............ 340-341 Series 758 See Series 728 ............ 342-343 Page Series 759 See Series 729 ............ 344-345 Series 750R See Series 730 ............ 346-347 Series 751R See Series 731 ............ 348-349 Series 752R See Series 732 ............ 350-351 Series 759R See Series 737 ............ 352-353 Series 758R See Series 738 ............ 354-355 Series 759 See Series 739 ........... 356-357 Series 760 See Series 760-763 .... 358-359 Device Minimum Meter Size Length Recommended (FNPT x FNPT) Inside Pit Diameter 5/8" 4" to 5" 18" 5/8" x 3/4" 4" to 5" 18" 3/4" 4" to 5" 20" 1" 5" to 6" 21" To order a 5/8" x 3/4" tandem meter setter having 3/4" double purpose ends, inlet valve only and a 7" height with 4" to 5" device length, you would order as follows: 750 -207 QN DD 33 Series 750, 751, 752, 753, 754, 755, 756, 757, 758, & 759 Tandem Meter Setters Meter Sizes: 5/8", 5/8" x 3/4", 3/4" and 1" Heights: 07", 09", 12", 15", 18", 21", 24" 12" minimum on 1" meter Other heights on special order Inlet/Outlet Options: All tandem setters are available with the same bottom bar inlet/outlet options as our standard horizontal copper meter setter. See Table I. Meter Valve/Nut Options: A = Check valve with plain meter nut (no lip) on outlet F = Angle dual check valve with plain meter nut (no lip) on outlet (ASSE 1024) K = Full port angle lockwing ball valve 300 PSIG P = Full port angle dual check valve (ASSE 1024) Q = Angle lockwing ball valve with plain meter nut (no lip) N = Flanged tubing with plain meter nut (no lip) 5/8", 5/8" x 3/4", 3/4", 1", 1 1/2", & 2" | Horizontal and Vertical Inlet / Outlet | Tandems Series 720, 721, 722, 723, 724, 725, 726, 727, 728, 729, 730, 731, 732, 737, 738, 739, 760-763, 770 See the Meter Setters section for pages.
